Intel's latest and greatest consumer chip, the Core i9-10900K has been criticized, including in our review, for its massive power consumption and all the heat it generates. But this new 10-core chip is an absolute overclocking beast, if you have the right equipment and you know how to use it, as I did when I set several world records, getting a clock speed as high as 7,083 MHz.
Due to its lower price and more reasonable power use, the Core i5-10600k is the daily driver of Intel's new Comet Lake S lineup. But the Core i9-10900K is the chip you take to the track on weekends. Yes, it uses a lot of power; it's loud, and it’s raw, but I don't care.
Intel’s 14nm++++++ (or whatever the current joke is) process is as refined as 110 octane fuel. The Core i9-10900K comes with more cores than the 9900K, overclocks better, has a stronger memory controller, runs cooler, and it’s priced handsomely. There is everything to like about these chips.
IHS and Lapping the Core i9-10900K OK, maybe my only gripe about the chips themselves is with the integrated heat spreader (IHS), mainly because it isn’t perfectly flat. I give this a pass, though, because neither AMD nor Intel have really buckled down on this side of things yet. Some argue it's better to have a convex heat spreader and a “bowed” water block or cooler, but I would tell you that if you flattened the IHS you would see improvement ten out of ten times. Sometimes very little, and sometimes a lot.
In and of itself, soldering metal to some well placed sand is mind boggling to me. Perhaps there is some warping because of the heat needed for soldering during manufacturing, or maybe it's not cost effective enough for the companies to care about doing a better job. If they can pass spec with looser quality control, I'm sure that’s the easy answer, on both sides, to the question.
Lapping, or a better term is probably ‘flattening the IHS,’ is what extreme overclockers (XOCers) and even some hardcore ambient users do to try to flatten both the chips’ heatspreader and the mating surface of a water block, air cooler, or LN2 container. That makes for a flat and even mating surface. Flatter surfaces require less thermal paste because it minimizes the voids and imperfections that have to be filled by thermal paste. It’s a simple equation: The thinner the layer of grease between the cooler and the hot heat spreader, the better the temps. The better the temps, the better the overclocking.
If you want to see lapping, search that on YouTube. If you’re like me, be prepared to look down at the clock and see that it’s 2 AM and you wasted your entire night watching people lap and perfectly ‘true’ (make flat) the surfaces.
So, how accurate can a guy, a pane of glass, sandpaper and a five gallon bucket of elbow grease get, you might wonder? Well, even for a neanderthal like me being cautious (but not careful), I got it down to a 0.01mm difference from edge to edge on the IHS (see below).
Is the Core i9-10900K Hot or Not? I was shocked when I first read that some leakers claimed the 10900K runs extremely hot. I had the exact opposite reaction. If so, how can I OC to 5.4 GHZ and not break 80C when the chip is under load? Well, it turns out motherboard companies are partially in charge of their own proprietary “boost” settings. These settings are based on taking a group of processors, seeing what they can handle voltage-to-MHz wise, and then taking an average. Some reviewers even showed Core voltage as high as 1.45V at default settings! That’s because many motherboards will turn on “multi core enhancement” by default, which locks in the turbo clock to all cores.
At 1.45v for 5-5.1 GHz, that’s a full 100mv more than what I use at 5.4 GHz on my CPU that loves to eat voltage. Is this to trick reviewers, or to confuse the public? You decide. I wish motherboard companies would leave well enough alone and rely on standards instead of playing tricks, but maybe it's just an oversight. There’s plenty of drama in the world at the moment without questioning this, so let’s get back to the positive.
Overclocking Memory and the Core i9-10900K Moving on, the memory controllers on the 10900K also appear to be an improvement over the controllers on the 9900K. It’s no struggle at all to hit frequencies above 4800MHz with low latency. 4000MHz and super low latency is also not a problem. Overclocking with 16GB sticks also seems to show a great improvement as well.
What I Used to Overclock the Core i9-10900K To get a sense of how well you can overclock the Intel Core i9-10900K, I tried it in two different testing scenarios, first with an AIO liquid cooler and then with my no-holds-barred LN2 (liquid nitrogen) cooling setup.
Ambient Cooling Test Bed
ASRock Z490 Aqua Prototype 2 Dimm MotherboardIntel Core i9-10900KG.Skill NEO 4000C19 2x16GBEnermax Maxtytan 1250W PSUEnermax Aquafusion 120x2 AIOThermal Grizzly Kryonaut LHE
Subzero Cooling Test Bed
ASRock Z490 Aqua Prototype 2 Dimm MotherboardIntel Core i9-10900KG.Skill NEO 3800C14 2x8GBEnermax Maxtytan 1250W PSUCustom High Surface Area Copper Ln2 Cooling PotThermal Grizzly Kryonaut LHE
Benchmate Suite 10.5
Cinebench R20
ASRock provided me with a prototype 2-DIMM version of the Z490 Aqua motherboard that should improve memory overclocking. I don't have a 4-DIMM version here to compare, but beyond the two slots being removed, the motherboard has the same VRM, and same components, etc., as the retail version. Judging by the success I had on this 2-DIMM version, I would more than expect the OC Formula line to be resurrected in the mainstream segment for Z5**.
Overclocking the Core i9-10900K with AIO Cooling
I used the Enermax Aquafusion 120mm x2 cooler to give me an idea of what the chips will do on a normal ambient AIO-cooled system. Overclocking for the sake of benchmarking is not equivalent to 100% stability by any means, but I will try to split the difference by using a heavily-threaded benchmark with AVX instructions for extra punishment. Cinebench R20 fits the bill.
On ambient cooling with the AIO, the Core i9-10900K is very basic and overclocks like a 9900K, but with a little less heat and a little more headroom. Not much tweaking can be done – changing the core voltage, system agent and the input/output voltage is about all that’s needed to max out the chip.
The Aquafusion was able to run the Core i9-10900K all the way up to 5.3 GHz at a 1.3Vcore and temperatures in the low 70’s. That’s a testament to how cool these processors run for being 10 core units.
Overclocking the Intel Core i9-10900K with LN2 It took some time to solve a few cold bug issues I encountered when I ran the chip on LN2, but when you work closely with top players in the industry that help debug the problems you’re having, there is such a sense of satisfaction when you solve them. Instead of just loading an LN2 profile and following a guide on what works, you have to test and problem solve. That can be a struggle at times, but it’s satisfying. That satisfaction is immeasurable when you defeat your competitor.
This is exactly what happened when I shocked ASUS by beating the results they achieved using liquid helium (-269C) with lowly liquid nitrogen (-196c), which is peasant-class in comparison. Liquid helium is the proverbial “pay to play” of extreme overclocking. It’s priced outrageously, and a full $4,000 tank can be gone in 30 minutes. Liquid nitrogen is “cheap” in comparison; 180 liters will cost you around $200-350 on average and last for days and days of benching.
As a competitive guy, I wouldn't say that I’m salty about others using liquid helium, but it definitely distorts the playing field. But I’ll never look down on anyone pushing things to the next level.
Once the problems with the cold bug were solved on my end, the scores started to roll in. I was able to push threaded benchmarks over 7 GHZ without much problem. This is a higher frequency than the best 9900K’s on record, by far.
Records achievedCinebench R11.5 10900KF @ 7036mhzCinebench R15 10900K @ 7003mhzCinebench R20 10900KF @ 6935mhzWprime1024 10900K @ 7085mhzGPUPi for CPU 1B 10900K @ 7081mhzGeekbench3 MultiCore 10900K @ 7000mhz
At the end of the day, these chips couldn't be more fun to overclock. You have incredible headroom, plenty of voltage scaling, and thanks to competition, a fair price for what it is. If you enjoy optimizing your system and benchmarking, this is the platform you would most likely enjoy spending your money on.
Due to its lower price and more reasonable power use, the Core i5-10600k is the daily driver of Intel's new Comet Lake S lineup. But the Core i9-10900K is the chip you take to the track on weekends. Yes, it uses a lot of power; it's loud, and it’s raw, but I don't care.
Intel’s 14nm++++++ (or whatever the current joke is) process is as refined as 110 octane fuel. The Core i9-10900K comes with more cores than the 9900K, overclocks better, has a stronger memory controller, runs cooler, and it’s priced handsomely. There is everything to like about these chips.
IHS and Lapping the Core i9-10900K OK, maybe my only gripe about the chips themselves is with the integrated heat spreader (IHS), mainly because it isn’t perfectly flat. I give this a pass, though, because neither AMD nor Intel have really buckled down on this side of things yet. Some argue it's better to have a convex heat spreader and a “bowed” water block or cooler, but I would tell you that if you flattened the IHS you would see improvement ten out of ten times. Sometimes very little, and sometimes a lot.
In and of itself, soldering metal to some well placed sand is mind boggling to me. Perhaps there is some warping because of the heat needed for soldering during manufacturing, or maybe it's not cost effective enough for the companies to care about doing a better job. If they can pass spec with looser quality control, I'm sure that’s the easy answer, on both sides, to the question.
Lapping, or a better term is probably ‘flattening the IHS,’ is what extreme overclockers (XOCers) and even some hardcore ambient users do to try to flatten both the chips’ heatspreader and the mating surface of a water block, air cooler, or LN2 container. That makes for a flat and even mating surface. Flatter surfaces require less thermal paste because it minimizes the voids and imperfections that have to be filled by thermal paste. It’s a simple equation: The thinner the layer of grease between the cooler and the hot heat spreader, the better the temps. The better the temps, the better the overclocking.
If you want to see lapping, search that on YouTube. If you’re like me, be prepared to look down at the clock and see that it’s 2 AM and you wasted your entire night watching people lap and perfectly ‘true’ (make flat) the surfaces.
So, how accurate can a guy, a pane of glass, sandpaper and a five gallon bucket of elbow grease get, you might wonder? Well, even for a neanderthal like me being cautious (but not careful), I got it down to a 0.01mm difference from edge to edge on the IHS (see below).
Is the Core i9-10900K Hot or Not? I was shocked when I first read that some leakers claimed the 10900K runs extremely hot. I had the exact opposite reaction. If so, how can I OC to 5.4 GHZ and not break 80C when the chip is under load? Well, it turns out motherboard companies are partially in charge of their own proprietary “boost” settings. These settings are based on taking a group of processors, seeing what they can handle voltage-to-MHz wise, and then taking an average. Some reviewers even showed Core voltage as high as 1.45V at default settings! That’s because many motherboards will turn on “multi core enhancement” by default, which locks in the turbo clock to all cores.
At 1.45v for 5-5.1 GHz, that’s a full 100mv more than what I use at 5.4 GHz on my CPU that loves to eat voltage. Is this to trick reviewers, or to confuse the public? You decide. I wish motherboard companies would leave well enough alone and rely on standards instead of playing tricks, but maybe it's just an oversight. There’s plenty of drama in the world at the moment without questioning this, so let’s get back to the positive.
Overclocking Memory and the Core i9-10900K Moving on, the memory controllers on the 10900K also appear to be an improvement over the controllers on the 9900K. It’s no struggle at all to hit frequencies above 4800MHz with low latency. 4000MHz and super low latency is also not a problem. Overclocking with 16GB sticks also seems to show a great improvement as well.
What I Used to Overclock the Core i9-10900K To get a sense of how well you can overclock the Intel Core i9-10900K, I tried it in two different testing scenarios, first with an AIO liquid cooler and then with my no-holds-barred LN2 (liquid nitrogen) cooling setup.
Ambient Cooling Test Bed
ASRock Z490 Aqua Prototype 2 Dimm MotherboardIntel Core i9-10900KG.Skill NEO 4000C19 2x16GBEnermax Maxtytan 1250W PSUEnermax Aquafusion 120x2 AIOThermal Grizzly Kryonaut LHE
Subzero Cooling Test Bed
ASRock Z490 Aqua Prototype 2 Dimm MotherboardIntel Core i9-10900KG.Skill NEO 3800C14 2x8GBEnermax Maxtytan 1250W PSUCustom High Surface Area Copper Ln2 Cooling PotThermal Grizzly Kryonaut LHE
Benchmate Suite 10.5
Cinebench R20
ASRock provided me with a prototype 2-DIMM version of the Z490 Aqua motherboard that should improve memory overclocking. I don't have a 4-DIMM version here to compare, but beyond the two slots being removed, the motherboard has the same VRM, and same components, etc., as the retail version. Judging by the success I had on this 2-DIMM version, I would more than expect the OC Formula line to be resurrected in the mainstream segment for Z5**.
Overclocking the Core i9-10900K with AIO Cooling
I used the Enermax Aquafusion 120mm x2 cooler to give me an idea of what the chips will do on a normal ambient AIO-cooled system. Overclocking for the sake of benchmarking is not equivalent to 100% stability by any means, but I will try to split the difference by using a heavily-threaded benchmark with AVX instructions for extra punishment. Cinebench R20 fits the bill.
On ambient cooling with the AIO, the Core i9-10900K is very basic and overclocks like a 9900K, but with a little less heat and a little more headroom. Not much tweaking can be done – changing the core voltage, system agent and the input/output voltage is about all that’s needed to max out the chip.
The Aquafusion was able to run the Core i9-10900K all the way up to 5.3 GHz at a 1.3Vcore and temperatures in the low 70’s. That’s a testament to how cool these processors run for being 10 core units.
Overclocking the Intel Core i9-10900K with LN2 It took some time to solve a few cold bug issues I encountered when I ran the chip on LN2, but when you work closely with top players in the industry that help debug the problems you’re having, there is such a sense of satisfaction when you solve them. Instead of just loading an LN2 profile and following a guide on what works, you have to test and problem solve. That can be a struggle at times, but it’s satisfying. That satisfaction is immeasurable when you defeat your competitor.
This is exactly what happened when I shocked ASUS by beating the results they achieved using liquid helium (-269C) with lowly liquid nitrogen (-196c), which is peasant-class in comparison. Liquid helium is the proverbial “pay to play” of extreme overclocking. It’s priced outrageously, and a full $4,000 tank can be gone in 30 minutes. Liquid nitrogen is “cheap” in comparison; 180 liters will cost you around $200-350 on average and last for days and days of benching.
As a competitive guy, I wouldn't say that I’m salty about others using liquid helium, but it definitely distorts the playing field. But I’ll never look down on anyone pushing things to the next level.
Once the problems with the cold bug were solved on my end, the scores started to roll in. I was able to push threaded benchmarks over 7 GHZ without much problem. This is a higher frequency than the best 9900K’s on record, by far.
Records achievedCinebench R11.5 10900KF @ 7036mhzCinebench R15 10900K @ 7003mhzCinebench R20 10900KF @ 6935mhzWprime1024 10900K @ 7085mhzGPUPi for CPU 1B 10900K @ 7081mhzGeekbench3 MultiCore 10900K @ 7000mhz
At the end of the day, these chips couldn't be more fun to overclock. You have incredible headroom, plenty of voltage scaling, and thanks to competition, a fair price for what it is. If you enjoy optimizing your system and benchmarking, this is the platform you would most likely enjoy spending your money on.
评论
发表评论